Ridder RW140 Product Manual Download Page 43

Page: 43 / 52

7.2 RLS/RSU limit-switch system

The RLS/RSU limit-switch system is a linear switch-system. The output shaft of the motor gearbox

operates the limit-switch system through a transmission. The number of revolutions of the output

shaft can be set between the end positions.

RLS: RW45\RW241/242

The switching range is 55, 86 or 97 revolutions of the drive shaft.

RSU: RW243/245/400/600\RW800\RW70/140

The switching range is 86, 120 or 860 revolutions of the drive shaft.

RLS/RSU

An RW motor-gearbox has a limit-switch system with connection nuts (4). Ridder does

not lock

the

adjusting rings (3). The drive unit can turn freely (temporarily, until the end positions are adjusted)

in the two directions. This

prevents damage

to the limit-switch system (before it is electrical

connected) when the motor is manually operated or is operated with electric tools!

1. THREADED SHAFT

2. KNURLED NUT

3. ADJUSTING RING

4. CONNECTION NUT

5. SWITCHING SPRING

6. STOPPER

7. HEX WRENCH 2 MM

a. ADJUSTING SCREW

LENGTH:

16 MM

b. ADJUSTING SCREW

LENGTH:

6 MM

8. SPARE PARTS

a, b

ES11/ES12

DUTY SWITCH

ES21/ES22

SAFETY SWITCH

Duty

switch

Safety

switches

Duty

switch

Duty

switch

Safety

switch

Duty

switch

Safety

switch

1. THREADED SHAFT

2. KNURLED NUT

3. ADJUSTING RING

4. CONNECTION NUT

5. SWITCHING SPRING

6. STOPPER

7. HEX WRENCH 2 MM

a. ADJUSTING SCREW

LENGTH:

16 MM

b. ADJUSTING SCREW

LENGTH:

6 MM

8. SPARE PARTS

a, b

ES11/ES12

DUTY SWITCH

ES21/ES22

SAFETY SWITCH

Do not go across the limits of the system when the motor is operated

manually or is operated with electric tools (with the hexagon socket

in the electric-motor shaft). This prevents damage or injury.

Ridder Drive Systems B.V.

+31 (0)341 416 854 -

+31 (0)341 416 611 -

ridder.com

Summary of Contents for RW140





















































Search results

Summary of Contents for RW140

Reviews:

Related manuals for RW140

Brands by name

Popular brands

Ridder RW140, Product Manual

Search results

Summary of Contents for RW140

Reviews:

Related manuals for RW140

Brands by name

Popular brands