User primary message
Explanation
No Analog Phone Line
An analog line is not detected as being plugged into the modem. If
the device is in Analog mode, this has a source of Fax. If the device is
in Fax Server mode, and the 'Enable analog receive' Fax Server
setting is set to 'On', this has a source of Fax Receive. If the device is
in Fax Server mode and the 'Enable analog receive' Fax Server
setting is set to 'Off', then this IR is not generated.
Memory Full, cannot print
faxes
Attempted print is automatically canceled. The Fax code will
recognize that the print job has been canceled and will not delete
pages in the fax job that have not printed. Fax will not attempt to
reprint the fax that generated the out of memory error until a POR is
performed.
Memory Full, cannot send
faxes
After a start, there is no memory to do the fax job. Attempted fax is
cancelled.
Fax server ‘To Format’ not set
up
Device is in Fax Server mode. The To format for the Fax Server setup
is null. Analog receive still possible.
Fax Station number not set up.
Held jobs may not be restored
This message is only posted once after the firmware has tried to
restore all of the jobs on disk, regardless of the number of held jobs
that were not restored. There are three versions of this IR, depending
upon cause. IRHeldA occurs when any other condition occurs which
stops the machine from restoring jobs from disk. These might include
disk failure, user abort, etc.
Held jobs may not be restored
(Insufficient Memory 37)
This message is only posted once after the firmware has tried to
restore all of the jobs on disk, regardless of the number of held jobs
that were not restored. There are three versions of this IR, depending
upon cause. IRHeldB occurs when the machine runs out of memory
while attempting to restore jobs from disk.
Held jobs may not be restored
(Config Change 57)
This message is only posted once after the firmware has tried to
restore all of the jobs on disk, regardless of the number of held jobs
that were not restored. There are three versions of this IR, depending
upon cause. IRHeldC occurs when the machine could not restore
jobs from the disk because the configuration of the machine has
changed. Some of these said configuration changes are code
version changes, paper handling option(s) removed, or the disk was
moved from a different model or speed of machine.
6. Troubleshooting
198
6
Summary of Contents for LI-MF1 M126
