Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 82

Page: 82 / 288

Copier / Document Server Features

❖

Original Type Priority

You can select the original type effective when the power is turned on, or
modes cleared.
The default setting is

Text

❖

Original Type Display

You can have the original types shown on the initial display.
The default setting is

Display

If you select

[

Hide

]

, the display is as below.

❖

Auto Image Density Priority

You can set whether Auto Image Density is "On" or "Off" when the machine
is turned on, reset, or modes are cleared.
The default setting for "Text" is

The default setting for "Text/Photo" is

The default setting for "Photo" is

Off

The default setting for "Pale" is

The default setting for "Generation Copy" is

❖

Copy Quality

You can adjust the quality level of copies for each original type (Text,
Text/Photo, Photo, Pale, Generation Copy).
• Text

Adjust text sharpness.
The default setting is

Normal

"Custom Setting" is the value set during service setup.
Choosing "Sharp" or "Sort" affects the outline sharpness of text.

• Text/Photo

When there are photo(s) and text on the original, select which takes prior-
ity.
The default setting is

Normal

"Custom Setting" is the value set during service setup.
"Normal" gives a balanced text and photo reproduction.

• Photo

For a photo original, adjust the finish quality level to match the type of
photo original.
The default setting is

Print Photo

"Custom Setting" is the value set during service setup.
Select "Print Photo" for printed photo originals, and "Coarse Print" for a
coarse dot finish, such as newspaper photos.
Select "Glossy Photo" for printed photo and text originals.

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands