Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 15

Page: 15 / 288

Connecting to the Interfaces

Connect the other end of the Ethernet cable to a network connection device
such as a hub.

Turn on the main power switch of the machine.

Indicator (green)
Lights up green when the machine is connected correctly to the network.

Indicator (yellow)
Lights up yellow when 100 BASE-TX is in operation. Goes off when 10
BASE-T is in operation.

Note

❒

For details about installing the printer driver, see "Preparing the Machine",
Printer Reference.

Reference

"Turning On the Power", About This Machine
"Preparing the Machine", Printer Reference

AME005S

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands