Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 199

Page: 199 / 288

Authentication Information

191

Registering a User Code

This section describes how to register a user code.

Press

[

System Settings

]

Press

[

Administrator Tools

]

Press

[

Next

]

Press

[

Address Book Management

]

Check that

[

Program / Change

]

is selected.

Press the name whose code is to be registered, or enter the registered
number using the number key.

If you press , you can search by the registered name, user code, fax number,
folder name, e-mail address, or IP-Fax destination.

Press

[

Auth. Info

]

Enter the user code using the number keys, and then press the

{

}

key.

If you make a mistake, press

[

Clear

]

or the

{

Clear/Stop

}

key.

Press

[

Next

]

twice.

Select the functions to be used with the user code from Available Func-
tions.

Press

[

]

To continue registering user codes, repeat the procedure from step

Press

[

Exit

]

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands