Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 24

Page: 24 / 288

Connecting the Machine

Note

❒

For the Effective Protocol setting, check that the protocol you want to use is
set to

[

Effective

]

❒

[

LAN Type

]

is displayed when the wireless LAN interface board is installed. If

both Ethernet and wireless LAN (IEEE 802.11b) are connected, the selected in-
terface takes precedence.

❒

SMTP Server and Fax E-mail Account must be specified in order to send In-
ternet Fax.

❒

When POP before SMTP is set to

[

]

, you must also make settings for Recep-

tion Protocol and POP3 / IMAP4 Settings.

❒

When SMTP Authentication is set to

[

]

, you must also make settings for

Administrator's E-mail Address.

❒

E-mail Communication Port and Fax E-mail Account must be specified in or-
der to receive Internet Fax.

❒

When setting POP before SMTP to

[

]

, check POP3 port number in E-mail

Communication Port.

Reference

p.47 “Interface Settings”
p.53 “File Transfer”

File Transfer

Reception Protocol

Necessary

File Transfer

POP3 / IMAP4 Settings

As required

File Transfer

Administrator's E-mail Address

As required

File Transfer

E-mail Communication Port

Necessary

File Transfer

E-mail Reception Interval

As required

File Transfer

Max. Reception E-mail Size

As required

File Transfer

E-mail Storage in Server

As required

File Transfer

Program / Change /
Delete E-mail Message

As required

File Transfer

Program / Change / Delete Subject

As required

File Transfer

Fax E-mail Account

Necessary

Menu

User Tool

Setting Requirements

Summary of Contents for Aficio IS 2425

































































































































































































































































































Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands

Ricoh Aficio IS 2425, Operating Instructions Manual

Search results

Summary of Contents for Aficio IS 2425

Reviews:

Related manuals for Aficio IS 2425

Brands by name

Popular brands