Ricoh Aficio IS 2425 Operating Instructions Manual Download Page 74 | Manualshive

Page: 74 / 288

background image

System Settings

66

2

❖

Program / Change / Delete LDAP Server

Program the LDAP server to find up e-mail destinations in the LDAP server
Address Book directly. This function is possible when sending scan files by e-
mail using the scanner or fax function.
To start an LDAP search, make sure that the items listed below are set. For
other items, check your environment and make any necessary changes.
• Server  Name
• Search  Base
• Port  No.
• Search Conditions
• Authentication method selection
To use the LDAP server in Administrator Tools, select

[

On

]

under LDAP server.

This function supports LDAP Version 2.0 and 3.0. Ver 2.0 does not support
High Security authentication.

❖

Use LDAP Server

Specify whether or not to use the LDAP server for searching.
The default setting is

Off

.

When Use LDAP Server is set to Off,

[

Search LDAP

]

will not appear on the

searching display.

❖

AOF (Always On)

Specify whether or not to use Auto Off.
The default setting is

On

.

❖

Firmware Version

You can check the version of the software installed in this machine.

❖

Network Security Level

For details about this function, consult your administrator.

❖

Reduce Recovery Time

You can specify whether or not to shorten the recovery time.
The default setting is

Off

.

If you press

[

On

]

, the recovery time is shortened.

If you press

[

Off

]

, the recovery time is lengthened and the machine's power

consumption is reduced.
This setting appears only if the copier unit and hard disk are installed in the
machine.

❖

Delete All Logs

For details about this function, consult your administrator.

❖

Transfer Log Setting

For details about this function, consult your administrator.

❖

Data Security for Copying

For details about this function, consult your administrator.

«
...
72
73
74
75
76
...
»

Summary of Contents for Aficio IS 2425

































































































































































































































































































Reviews:

No comments

Related manuals for Aficio IS 2425

Brand: DataCard Pages: 2

Brand: Oki Pages: 152

Brand: Oki Pages: 140

Brand: Oki Pages: 181

Brand: Oki Pages: 52

Brand: Oki Pages: 229

Brand: Oki Pages: 224

Brand: Oki Pages: 141

Brand: Oki Pages: 160

Brand: Oki Pages: 48

Brand: Oki Pages: 20

Brand: Oki Pages: 52

Brand: Oki Pages: 127

Brand: Oki Pages: 128

Brand: Oki Pages: 12

Brand: Oki Pages: 41

Brand: Oki Pages: 35

Brand: Oki Pages: 165

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands