Ricoh AC204 Operating Instructions Manual Download Page 76

Page: 76 / 192

RINTING

5.15

Using a Page Overlay

After an overlay has been created, it is ready to be printed with
your document. To print an overlay with a document:

Create or open the document you want to print.

When you change the print settings from your software
application, access the printer properties. See page 5.2.

Click the Extras tab.

Select the overlay you want to print from the Overlay
drop-down list box.

When the overlay file doesn’t appear on the Overlay List,
click the Edit button and Load Overlay, and select the
overlay file.

If you have stored the overlay file you want to use into an
external source, you can also load the file when you access
this Load Overlay window.

After you select the file, click Open. The file is now shown
in the Overlay List box and is available for printing. Select
the overlay from the Overlay List box.

Summary of Contents for AC204

































































































































































































Search results

Summary of Contents for AC204

Reviews:

Related manuals for AC204

Brands by name

Popular brands

Ricoh AC204, Operating Instructions Manual

Search results

Summary of Contents for AC204

Reviews:

Related manuals for AC204

Brands by name

Popular brands