Ricoh AC204 Operating Instructions Manual Download Page 22

Page: 22 / 192

ETTING

STARTED

1.11

If you want to use a parallel printer cable, only use a IEEE
1284 compliant cable and connect it to the parallel
connector on your machine.

OTE

• To connect the machine to the parallel port of the computer

requires a certified parallel cable.
You will need to buy the a IEEE 1284 compliant cable.

• You only need to connect one of the above cables.

• If you are using a USB cable, you must be running Windows 98/

Me/2000/XP.

• When using the a USB connection, your machine provides two

USB modes; Fast and Slow. Fast is the default mode. Some PC
user may experience poor USB function in the default mode. If
this occurs, select the Slow mode to achieve successful results.
For details on changing the USB mode, see page 8.16.

Summary of Contents for AC204

































































































































































































Search results

Summary of Contents for AC204

Reviews:

Related manuals for AC204

Brands by name

Popular brands

Ricoh AC204, Operating Instructions Manual

Search results

Summary of Contents for AC204

Reviews:

Related manuals for AC204

Brands by name

Popular brands