manualshive.com logo in svg

Ricoh AC204, Operating Instructions Manual

Share
Download
Ricoh AC204 Operating Instructions Manual Download Page 3

vi

Safety Information

When using this machine, the following safety precautions should always be followed.

Safety During Operation

In this manual, the following important symbols are used: 

 WARNING:

 

WARNING:

Indicates a potentially hazardous situation which, if instructions are 
not followed, could result in death or serious injury.

 CAUTION:

Indicates a potentially hazardous situation which, if instructions are not 
followed, may result in minor or moderate injury or damage to property.

• Connect the power cord directly into a wall outlet and never use an 

extension cord.

• Disconnect the power plug (by pulling the plug, not the cable) if the power 

cable or plug becomes frayed or otherwise damaged.

• To avoid hazardous electric shock or laser radiation exposure, do not 

remove any covers or screws other than those specified in this manual.

• Turn off the power and disconnect the power plug (by pulling the plug, not 

the cable) if any of the following occurs:

•You spill something into the machine.

•You suspect that your machine needs service or repair.

•The external housing of your machine has been damaged.

• Do not incinerate spilled toner or used toner. Toner dust might ignite when 

exposed to an open flame.

• Disposal can take place at our authorized dealer.

• Dispose of the used toner bottle in accordance with the local 

regulations.

• Keep the machine away from flammable liquids, gases, and 

aerosols. A fire or an electric shock might occur.

Summary of Contents for AC204

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands