Ricoh 161 Function Manual Download Page 65 | Manualshive

Page: 65 / 192

background image

Specifying a Destination

57

1

Redial

The machine stores the latest destinations specified for each transmission meth-
od. This function saves time when you are sending to the same destination re-
peatedly, as you do not have to enter the destination again.

Important

❒

The following kinds of destinations are not stored:
• Destinations specified using the destination list
• Destinations specified as a group destination
• Destinations dialed using the external telephone
• Destinations dialed by Redial (regarded as already stored in memory)
• Second and later destinations broadcasted to
• Destinations specified in the LAN-Fax Driver on the computer

❒

To redial a fax number, do not dial any numbers before you press the

{

Pause/Redial

}

key. If you press the

{

Pause/Redial

}

key after entering numbers

using the number keys, a pause is entered instead.

A

Place the original, and then select the scan settings you require.

B

Press the

{

Pause/Redial

}

key.

C

Select the destination you want to redial to using

{U}

or

{T}

, and then

press the

{

OK

}

key.

D

Press the

{

Start

}

key.

ASO027S

«
...
63
64
65
66
67
...
»

Summary of Contents for 161

































































































































































































Reviews:

No comments

Related manuals for 161

Brand: Xerox Pages: 414

Brand: Xante Pages: 21

Brand: Javelin Pages: 2

WorkCentre 7655

Brand: Xerox Pages: 19

Brand: Citizen Pages: 133

Brand: Xerox Pages: 2

Brand: Olivetti Pages: 228

Brand: 3nStar Pages: 8

Brand: Pantum Pages: 111

5550N - Phaser B/W Laser Printer

Brand: Xerox Pages: 16

Brand: MIMAKI Pages: 28

Brand: Lexmark Pages: 807

Ecosys FS-1800+

Brand: Kyocera Mita Pages: 31

Brand: Microcom Pages: 207

Brand: Kyocera Pages: 28

Brand: OKIDATA Pages: 39

Brand: Xerox Pages: 18

Brand: Wasp Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands