Ricoh 161 Function Manual Download Page 16

Page: 16 / 192

Machine status and message

Destination entry

Selection keys

Switches the destination between

fax number, e-mail address and IP-
Fax destination.

Selectable items

Note

❒

The display will differ depending on installed optional units.

❒

You can change Internet Fax setting under E-mail Settings in the Fax Features
menu.

❒

You can change IP-Fax settings under IP-Fax Settings in the Fax Features
menu.

Reference

p.13 “Transmission Modes”
p.53 “Specifying a destination using the Quick Dial key”
p.62 “Searching for a Destination in the Address Book”
“Fax Features”, General Settings Guide
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide

ALT009S

Summary of Contents for 161

































































































































































































Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands

Ricoh 161, Function Manual

Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands