Ricoh 161 Function Manual Download Page 135 | Manualshive

Page: 135 / 192

background image

Printing Options

127

3

Just size printing

If you enable this function, received documents are printed on the sheet that has
the highest priority.
This function is enabled with User Parameters (switch 05, bit 5) in the Fax Fea-
tures menu.
If the paper tray is not stocked with paper of a suitable size to print a received doc-
ument, a message appears on the display prompting you to load paper of the re-
quired size. When you have loaded new paper, press

[

Exit

]

to print the document.

Note

❒

After pressing

[

Exit

]

, procedure varies depending on machine status when the

message occurred.
• If any received documents or reports were being printed automatically, the

printer automatically continues printing from where it left off.

• If any documents or reports were being printed manually, the printer does

not resume printing. Perform the operation from the beginning again.

Reference

“Fax Features”, General Settings Guide

«
...
133
134
135
136
137
...
»

Summary of Contents for 161

































































































































































































Reviews:

No comments

Related manuals for 161

Brand: Oki Pages: 2

Brand: Xerox Pages: 11

Brand: Xerox Pages: 30

Versant 4100 Press

Brand: Xerox Pages: 68

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Versant 2100 Press

Brand: Xerox Pages: 68

DocuPrint C2200

Brand: Xerox Pages: 200

Brand: J&Maya Pages: 21

Brand: U-Line Pages: 18

Brand: Magicard Pages: 124

Accel a Writer 812

Brand: Xante Pages: 312

Brand: Tandy Pages: 83

Brand: Intermec Pages: 282

Brand: Oki Pages: 175

Brand: TallyGenicom Pages: 208

Magicolor 2 Desklaser

Brand: MINOLTA-QMS Pages: 12

magicolor 2300 DL

Brand: MINOLTA-QMS Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands