Ricoh 161 Function Manual Download Page 18

Page: 18 / 192

❖

E-mail Settings

❖

IP-Fax Settings

Function name

Description

Internet Fax Settings

You can select to display

or not.

When you want to send an Internet Fax, set
On to display the icon.

Maximum E-mail Size

Use this setting to limit the size of sent e-
mail, so that destinations that refuse e-mail
over a certain size can still receive your e-
mail. When this function is set to on, you
cannot send e-mail that is larger than the
specified limit.

SMTP RX File Delivery

This function is available on systems that al-
low routing of e-mail received via SMTP.

Function name

Description

Enable H.323

Specify whether or not H.323 is used for IP-
Fax transmission.

Enable SIP

Specify whether or not SIP is used for IP-Fax
transmission.

H.323 Settings

Set the IPv4 address or host name of gate
keeper, and alias telephone number.

SIP Settings

Set the SIP server's IPv4 address and SIP user
name.

Gateway Settings

Register, change, or delete the gateway used
for transmission to IP-Fax. Register to use the
gateway without using the gatekeeper/SIP
server.

Summary of Contents for 161

































































































































































































Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands

Ricoh 161, Function Manual

Search results

Summary of Contents for 161

Reviews:

Related manuals for 161

Brands by name

Popular brands