Ricoh 161 Function Manual Download Page 120 | Manualshive

Page: 120 / 192

background image

Reception

112

3

Receiving documents according to parameter-specified settings

If one of the conditions in the following list occurs, the machine receives only
those documents that match the conditions specified in the User Parameters
(switch 05, bit 2, 1) in the Fax Features menu.

You can specify the following conditions with the User Parameters (switch 05, bit 2, 1)
in the Fax Features menu.
• When Own Name or Own Fax Number is received

The machine switches to Substitute Reception only when the sender has pro-
grammed their Own Name or Own Fax Number. If the power is switched off
for more than twelve hours, all the documents stored in memory are deleted.
In this case, the Journal can be used to identify the senders of the deleted doc-
uments, so you can ask them to resend.
If a sender has not programmed their Own Name or Own Fax Number, the
machine may fail to receive an important fax document. It is recommended
that you ask important senders to program an Own Name or Own Fax
Number in advance.

• Free

The machine switches to Substitute Reception regardless of whether or not
the sender has programmed their Own Name or Own Fax Number.

• Disable

The machine does not receive any documents.

Reference

“Fax Features”, General Settings Guide
“Adding Paper and Replacing Toner”, Troubleshooting
“Clearing Misfeeds”, Troubleshooting

Problems

Causes

Solutions

h

is lit.

Paper is jammed.

Remove the jammed paper.

For details about removing the paper, see
“Clearing Misfeeds”, Troubleshooting.

B

is lit.

All trays are out of paper.

Add paper. For details about adding
paper, see “Adding Paper and Re-
placing Toner”, Troubleshooting.

G

is lit.

Toner is empty.

Replace the toner bottle. For details
about replacing the toner bottle, see
“Adding Paper and Replacing Ton-
er”, Troubleshooting.

The message “

Problem

with this tray.

”

appears.

All trays are out of action.

Call your service representative.

«
...
118
119
120
121
122
...
»

Summary of Contents for 161

































































































































































































Reviews:

No comments

Related manuals for 161

Brand: SPRT Pages: 28

Brand: NCR Pages: 224

SelfServ Checkout 7350

Brand: NCR Pages: 20

VarioPrint 6000 MICR series

Brand: Oce Pages: 264

Brand: Oce Pages: 194

Brand: TASKalfa Pages: 36

Brand: OEC Pages: 28

imageRUNNER ADVANCE C350iF

Brand: Canon Pages: 102

imageRUNNER ADVANCE C2230

Brand: Canon Pages: 12

Brand: Canon Pages: 598

Brand: Oki Pages: 320

Brand: SATO Pages: 2

Brand: DNP Pages: 66

MAGICARD 300plus

Brand: Ultra electronics Pages: 45

Brand: Oki Pages: 143

Brand: Citizen Pages: 57

Brand: Konica Minolta Pages: 3

Brand: Kashino Technology Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands