background image

Before you begin        15

DANSK

Liste over advarsler og sikkerhedsregler

ADVARSLER

1.

INSTALLATION AF RETROSCAN-SKANNESYSTEMET MÅ KUN
FORETAGES AF UDDANNET PERSONALE, SOM ER FULDT
FORTROLIGT MED SIKKERHEDSPROCEDURERNE OG BEKENDT MED
GÆLDENDE LOVGIVNING I DET LAND, HVOR SYSTEMET ANVENDES.

SIKKERHEDSREGLER

1.

FØLG ALTID PROCEDURERNE FOR, HVORDAN MAN UNDGÅR STATISK
ELEKTRICITET. FØLGES DE IKKE, KAN DET RESULTERE I
BESKADIGELSE AF PROBENS INTERFACEKORT.

2.

FOR AT UNDGÅ BESKADIGELSE AF PROBEN, NÅR DEN BEVÆGER SIG
I Z-RETNINGEN, ER DET VIGTIGT AT SØRGE FOR, AT NÅR DER
VÆLGES EN UNBRAKOSKRUE ELLER ET FAST STED, HVOR
TAPSAMLINGEN KAN PLACERES, BEVÆGER DET VALGTE STED SIG I
Z-RETNINGEN SAMMEN MED SPINDELEN.

3.

PROBENS INTERFACEKORT KAN BLIVE BESKADIGET AF STATISK
ELEKTRICITET. DERFOR ANBEFALES DET ALTID AT ANVENDE ET
ANTISTATISK ARMBÅND MED EN PASSENDE JORDFORBINDELSE, NÅR
KORTET BERØRES. BEVÆGELSER, SOM KAN GENERERE STATISK
ELEKTRICITET, BØR OGSÅ HOLDES PÅ ET MINIMUM.

4.

NEDENSTÅENDE INSTRUKTIONER ER GENERELLE. HVIS DER ØNSKES
SPECIFIKKE OPLYSNINGER/INSTRUKTIONER OM, HVORDAN
INTERFACEKORTET SKAL INSTALLERES I DEN PERSONLIGE
COMPUTER (PC), KAN MAN SE I BRUGERVEJLEDNINGEN ELLER DEN
TEKNISKE VEJLEDNING, SOM FULGTE MED PC'EN.

5.

NÅR PROBEKABLET TRÆKKES FRA SP2-1-PROBEN TIL PC'EN, ER DET
VIGTIGT, AT KABLET HOLDES PÅ FORSVARLIG AFSTAND AF
BEVÆGELIGE DELE, SOM KABLET KAN HÆNGE FAST I, ELLER SOM
KAN SKÆRE KABLET OVER, NÅR VÆRKTØJSMASKINEN ER I
BEVÆGELSE. DET ER OGSÅ MEGET VIGTIGT, AT DER GIVES SÅ
MEGET EKSTRA KABEL, AT VÆRKTØJSMASKINEN KAN BEVÆGE SIG I
HELE SIT ARBEJDSOMRÅDE UDEN AT STRÆKKE KABLET.

Summary of Contents for RETROSCAN































































Reviews: