background image

 

City Series

  |    

13

installation

Caution Requirements

The top, back and sides of the ireplace are deined by 

standoffs. The metal ends of the standoff may 

NOT

 be 

recessed into combustible construction.

WARNING

Fire hazard is an extreme risk 

if these clearances (air space) to combustible materials are not 

adhered to. It is of greatest importance that this ireplace and vent 

system be installed only in accordance with these instructions.

Clearances CV40E (single sided)

The clearances listed below are Minimum distances unless otherwise stated:

A major cause of chimney related ires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this 
ireplace and vent system be installed only in accordance with these instructions.

Note: CV40E (single sided unit) clearances listed on this page - for CB40E (3 sided) see next page.

Clearance: single sided

Dimension

Measured From:

A: Mantel Height (min.)

**

Top of Fireplace Opening

B1:From Floor

25-9/16" (649mm)

Top of Fireplace Opening

B2: Opening Height

15-1/16" (383mm)

Bottom/Top of Fireplace Opening

C: Sidewall (on one side)

8-1/2" (216mm)

Side of Fireplace Opening

D: Mantel Depth (max.)

**

E: Alcove Width

84" (2134mm)

Sidewall to Sidewall (Minimum)

 F: Alcove Depth

36" (914mm)

Front to Unit (Maximum)

G: Ceiling
    (in front of ireplace)

37-1/2" (953mm)

Top of Fireplace Opening

H: Convection Air Outlet

*

Top of Enclosure

J: Convection Air Outlet Opening Ofset

0-3" (76mm)

Max. ofset from top of chase enclosure

K: Chase Enclosure (Min.)

63" (1600mm)

From base of unit/loor

Hearth

0"

No hearth required

** 

See mantel clearances chart in this manual.

Flue Clearances to Combustibles

Horizontal - Top

3"

Horiztonal - Side 

2"

Horiztonal - Bottom

2"

Vertical

2"

Passing through wall/
f l o o r / c e i l i n g   -   w h e n 

irestop is used.

1-1/2"

Alcove

E

F

D

A

C

B

1

G

B

2

J

H

K

The 

HeatWave

 Duct Kit has differ-

ent clearance and framing require-
ments, check the 

HeatWave

 manual 

for details.

CV40E- Single sided

*

A minimum of 120 square 

inches of open area, not 
lower than 3" from top of 
enclosure, required for all 
installations 

Summary of Contents for City Series CB40E-LP





































































































Reviews: