Regency City Series CB40E-LP Owners & Installation Manual Download Page 3 | Manualshive

Page: 3 / 100

background image

City Series

|

3

MANUFACTURED MOBILE HOME REQUIREMENTS

INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE

This Regency

®

product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following standards: VENTED GAS

DECORATIVE FIREPLACE CAN/CGA-2.17-M91, and ANSI Z21.50-2014 • CSA 2.22-2014

.

and GAS-FIRED APPLIANCES FOR USE AT

HIGH ALTITUDES CAN/CGA 2.17-M91.

This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.

This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes
follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the
current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.

This Regency

®

mobile/manufactured home listed appliance comes factory equipped with four 1/4" diameter holes located near each corner

of the base. Fasten the ireplace in place using screw, inserted through the holes.

This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local
codes. See the "Wiring Diagram" section.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

This appliance may only be installed in an aftermarket permanently located, manufactured home (U.S.A only) or mobile home, where not
prohibited by local codes.

This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other cases,
unless a certiied kit is used.

Ensure that structural members are not cut or weakened during installation.

«
1
2
3
4
5
...
»

Summary of Contents for City Series CB40E-LP





































































































Reviews:

No comments

Related manuals for City Series CB40E-LP

Brand: e-Flame USA Pages: 9

Brand: RealFlame Pages: 14

Brand: pleasant hearth Pages: 2

Comfort Glow CGFB32CB

Brand: Desa Pages: 36

Brand: Napoleon Pages: 3

Brand: KEKAI Pages: 98

CC-RON00-1X0 Ronda 160

Brand: Nordpeis Pages: 36

Brand: kozy heat Pages: 8

Brand: UBERHAUS DESIGN Pages: 9

Brand: Febo Flame Pages: 9

Brand: Febo Flame Pages: 10

Brand: Dik Geurts Pages: 52

Brand: Outdoor Lifestyles Pages: 24

Brand: Hearth and Home Technologies Pages: 2

Heat-Zone HZLIN-ADP

Brand: Hearth and Home Technologies Pages: 3

Brand: Hearth and Home Technologies Pages: 11

JETMASTER 700 D

Brand: The Fireplace Pages: 4

Brand: GRAND EFFECTS Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands