Regency Fireplace Products Greenfire GF1500L Owners & Installation Manual Download Page 9

Page: 9 / 76

Greenfire® GF1500L-2 Gas Fireplace

| 9

Clearances

The clearances listed below are minimum distances unless otherwise stated.

A major cause of chimney-related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
fireplace and flue system be installed only in accordance with these instructions.

Clearance:

Dimension

Measured From:

A: Mantel Height (min.)

254 mm

Top of fireplace opening/hot air outlet

B: Sidewall (on one side)

152 mm

Side of fireplace opening/hot air outlet

C: Ceiling (room and/or alcove)

1162 mm

Top of fireplace opening/hot air outlet

D: Mantel Depth (max.)

305 mm

730 mm above fireplace opening/hot air
outlet

E: Alcove Width

1524 mm

Sidewall to sidewall (minimum)

F: Alcove Depth

914 mm

Front to back wall (maximum)

G: From Floor

617 mm

Top of fireplace opening/hot air outlet

Note:

No hearth required

Installed close
to ceiling.

Flue Clearances to Combustibles

Horizontal - Top

76mm

Horizontal - Side

51mm

Horizontal - Bottom

51mm

Vertical

51mm

Alcove

Installed Close

to Floor

installation

UTION

• The top, back and sides of the fireplace are defined by

standoffs. The metal ends of the standoff may NOT be
recessed into combustible construction.

ARNING

Fire hazard is an extreme risk

• If these clearances (air space) to combustible

materials are not adhered to. It is of greatest

importance that this fireplace and flue system be

installed only in accordance with these instructions.

Summary of Contents for Greenfire GF1500L













































































Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF1500L, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands