Greenfire® GF1500L-2 Gas Fireplace
| 55
installation
Operating Instructions
Before operating this appliance, proceed through the
following check list.
1. Read and understand these Instructions before
operating this appliance.
2. Check to see that all wiring is correct and enclosed
to prevent possible shock.
3. Check to ensure there are no gas leaks.
4. Make sure the glass door is in place. Never oper-
ate the appliance with the door glass removed.
5. Verify that all flueing and the termination cap is
unobstructed.
6. Verify log placement.
7. The unit should never be turned off and on again
without a minimum of a 60 second wait.
8. When lighting the appliance, the inside of the glass
may fog up. This will burn off after a few minutes
of operation.
Lighting Instructions
1. Plug the power cord into a power outlet or turn
on adjacent isolation switch.
2. There is a black, manual, ON/OFF button located
in the bottom left-hand corner of the unit. This
button can be used if there is no remote control.
The flame / fan patterns cannot be changed when
using this button.
3. After approximately 3 seconds the spark ignition
system will spark for 25 seconds to light the pilot
burner, then main burner will light.
4. If the main burner does not light, repeat step 2 to
restart the unit. See page 39 on "Resetting the
unit".
Shutdown Instructions
1. Press the ON/OFF switch once.
2. Turn off all electric power to the appliance if service
is to be performed.
Fan Operation
Set the fan speed on the control panel at the top
rear of the unit to adjust to the desired speed.
Pressing and releasing the plus (+) FAN button
will change the fan speed as follows:
LOW -> MEDIUM -> HIGH -> .
FAN CANNOT BE TURNED OFF
Pressing and releasing the minus (-) FAN button
will be the reverse of the above.
Adjusting Flame Height
There are six flame settings that can be adjusted
by pressing and releasing the plus (+) and minus
(-) FLAME button.
Summary of Controls
On/Off Button
If the unit is switched off, pressing and releasing
this button once will switch the unit on. The unit will
resume its last settings.
Fan must be running at all times
when the unit is in operation.
Remote Control
Use the Regency Remote Control Kit supplied
with this unit. Use of other systems may void your
warranty. See page 2 for pairing of remote.
The remote control kit comes with a hand held
transmitter and a wall mounting plate.
Choose a convenient location to mount the hand
held transmitter, protection from extreme heat is
very important.
By using the wall mounting plate to house the
transmitter, the remote can also be used as a
wall thermostat.
NO
TES
• The main burner will always start on
"HIGH" and resume it's last setting after
20 seconds of operation.
• When the glass is cold and the appliance
is lit, it may cause condensation and fog
the glass. This condensation is normal
and will disappear in a few minutes as the
glass heats up.
• Do not attempt to clean the glass while
it is still hot!
• Do not burn the appliance without the
glass front in place.
First Fire
The
FIRST FIRE
in your heater is part of the paint
curing process. To ensure that the paint is properly
cured, it is recommended that you burn your fireplace
for at least four (4) hours the first time you use it.
When first operated, the unit will release an odour
caused by the curing of the paint and the burning
off of any oils remaining from manufacturing. Smoke
detectors in the house may go off at this time. Open
a few windows to ventilate the room for a couple of
hours. The glass may require cleaning.
If the unit is switched on, pressing and releasing
this button once will switch the unit off.
Flame:
Increase -
If the unit is switched on, pressing
and releasing the flame plus (+) button once will
increase the flame height to the next available
high setting.
Decrease -
If the unit is switched on, pressing
and releasing the flame minus (-) button once
will decrease the flame height to the next avail-
able low setting.
Fan:
Increase -
If the unit is switched on, pressing
and releasing the fan plus (+) button once will
increase the fan speed to the next available
high setting.
Decrease -
If the unit is switched on, pressing
and releasing the fan minus (-) button once will
decrease the fan speed to the next available
low setting.
NO
TES
• The fan will not completely turn off on
this unit.
• The heater turns off when the room
temperature reaches 1
o
C over the set
temperature and turns back on when
the room temperature reaches 0.5
o
C
under the set temperature when in
AUTO mode.
