Regency Fireplace Products Greenfire GF1500L Owners & Installation Manual Download Page 13

Page: 13 / 76

Greenfire® GF1500L-2 Gas Fireplace

| 13

installation

Clearances for Combustible Finishing with Mantel

Combustible Mantel Leg Clearances

Mantel leg & combustible finishing clearances are shown in the diagram below.

Combustible Material

(152mm)

(305mm)

(0)

(630 mm)

To unit base

(322 mm)

Top of

Fireplace

Opening

(576 mm)

(305mm)

(470 mm)

(241mm)

Combustible

Stud

(On Edge)

Nailing Flange

Combustible facing

(min. 10mm- max. 19mm)

(297 mm)

(200mm)

(100mm)

(372 mm)

Allowable mantel

leg projection

181mm

254mm

330mm

38mm

MANTEL LEG

102mm

178mm

Allowable mantel

leg projection

181mm

254mm

330mm

38mm

MANTEL LEG

102mm

178mm

Allowable mantel

leg projection

181mm

254mm

330mm

38mm

MANTEL LEG

102mm

178mm

13mm Gap

Combustible

Important:

Due to the extreme heat this fireplace emits, the mantel clearances are
critical.

Combustible finishing and mantel clearances are shown in the diagram on the
right. Finishing trim must be used with combustible finishing.

TES

•

Maximum combustible finishing material thickness is 19 mm, mea-

sured from the front of the fireplace opening. If total finishing material

is greater than 19 mm, non combustible material must be used.

•

Use high quality paint on the mantel and facing, or the paint may
discolour.

•

Combustible mantel starts at 796 mm (618 mm + 178 mm) from
the unit's base.

Summary of Contents for Greenfire GF1500L













































































Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF1500L, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands