Regency Fireplace Products Greenfire GF1500L Owners & Installation Manual Download Page 45

Page: 45 / 76

Greenfire® GF1500L-2 Gas Fireplace

| 45

installation

Optional WIFI App (Part #946-767) - WIFI Dongle Installation

920-376

05.05.21

WIFI App / WIFI Dongle Installation Instructions

1. Remove the four Phillips head screws on the front panel plate to gain

access to the ECS V control module.

2. Locate the WIFI dongle connection on the left side of the ECS V control

module.

3. Line up the tab on the controller with the notches on the dongle.

4. Insert the dongle cable into the controller and make sure it is properly seated.

5. Apply Velcro strips to the bottom of the dongle and the inside of the unit

and place the control module and dongle inside the unit.

Front panel plate removed

WIFI dongle connection

Properly seated:

6. Reverse step 1 to close the unit.

Improperly seated:

• If the appliance was completed with finishing materials and ac-

cess to the ECS V cannot be gained from the front panel, see

manual regarding how to access the WIFI dongle connection.

Once access is gained, proceed to step 2.

Use this QR code to access our quick start guide.

IMPOR

TANT

• See warnings and release on next page.

Module

Dongle

WiFi dongle/app quick start guide.

Summary of Contents for Greenfire GF1500L













































































Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF1500L, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands