Regency Fireplace Products Greenfire GF1500L Owners & Installation Manual Download Page 48

Page: 48 / 76

48 |

Greenfire® GF1500L-2 Gas Fireplace

installation

GF1500

07 february 22

919-592a

OPTIONAL FAN KIT INSTALLATION

FAN DUCT EXTENSION KIT

In order to use the fan extension duct kit, you must have

fan kit. This kit allows you to extend the fan duct to 9m.

1. Attach the connecting collar to the duct that came with the duct kit.

Use the screws provided.

2. Attach the 4.5m duct within this kit to the connecting collar on the opposite

end with the screws provided. Extend the flex to the desired length.

WIRING DIAGRAM

Caution: Ensure that the wires do not touch any hot surfaces

and are away from sharp edges.

Alternate Switches: May use the following. Check with local authorities and electrician.

CLIPSAL 203 2E45 OUD - Dimmer

CLIPSAL 2031 VF3CSF - 3 Speed

CAUTION: Label all wires prior to dis-

connection when servicing controls.

Wiring errors can cause improper and

dangerous operation

ON/OFF Switch

Wire

Brown

Blue

Earth

240V-50Hz

Brown (Hot)

Blue (Neutral)

(Earth)

Fan

Blue-Neutral Brown-High Red-Low

Green

Heat Zone Unit

Summary of Contents for Greenfire GF1500L













































































Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF1500L, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF1500L

Reviews:

Related manuals for Greenfire GF1500L

Brands by name

Popular brands