Valcourt FG00001 Installation Instructions Manual Download Page 1

  

DANGER

HOT GLASS

 WILL CAUSE BURNS. 

DO NOT TOUCH

 GLASS UNTIL 

COOLED. 

NEVER

 ALLOW CHILDREN  TO TOUCH GLASS. A barrier 

designed to reduce the risk of burns from the hot viewing glass is provided 
with this appliance and shall be installed for the protection of children and 
other at-risk individuals. NOTE : Barrier required, may be sold separately.

Printed in Canada

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE

WARNING

46139_IA

2022-01-24

MODEL

L48

 

(FG00001 & FG00010)

DIRECT VENT  

ZERO CLEARANCE 

GAS FIREPLACE HEATER

MULTIFUNCTION REMOTE (MF)

ENGLISH

 FIRE OR EXPLOSION HAZARD 

•  Failure to follow safety warnings exactly could result in 

serious injury, death or property damage.
•  Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

 WHAT TO DO IF YOU SMELL GAS 

•  Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any phone 

in your building.
•  Leave the building immediately.
•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.
•  If you cannot reach your gas supplier, call the fire department.
•  Installation and service must be performed by a qualified 

installer, service agency or the gas supplier.

 WARNING 

•  If not installed, operated and maintained in accordance 

with the manufacturer’s instructions, this product could 

expose you to substances in fuel or from fuel combustion 

which can cause death or serious illness.
•  This appliance may be installed in an aftermarket, 

permanently located, manufactured home (USA only) or 

mobile home, where it is not prohibited by local codes.
•  This appliance is only for use with the type of gas 

indicated on the rating plate.
•  This appliance is not convertible for use with other 

gases, unless a certified kit is used.
•  Fuels used in gas, wood-burning or oil fired appliances, and 

the products of combustion of such fuels, contain chemicals 

known to the State of California to cause cancer, birth defects 

or other reproductive harm. For more information go to   

www.P65warnings.ca.gov/

INSTALLATION 

INSTRUCTIONS

Safety tested

according to ANSI Z21.88-2017

and CSA 2.33-2017 standards

by an accredited laboratory.

Summary of Contents for FG00001































































Reviews: