Regency Fireplace Products City ACB40ELP Owners & Installation Manual Download Page 68

Page: 68 / 87

City Series ACB40E

installation

919-674

06.09.16

CB40E INNER PANELS

1. Install inner lower base panel.

2. Install panel clips into the slots at the top of the panel as shown.

3. Manoeuvre in back panel to the back wall of the unit—secure in place

with 2 panel clips and 2 screws.

CB40E OUTER PANELS

Outer side panel install

Outer base panel install

Note: Install inner safety glass prior to installation of outer panels-see
instructions in manual

1. Attach Regency logo to the right hand side of outer front panel. The

magnets will be positioned under the outer front base panel to
secure

the logo. The logo should be about

76 mm

from the right

hand corner

of the outer base. Install outer front base panel.

2. Install side panel - the side panel is secured in place by existing

magnets in the unit.

The CB40E can be equipped with optional steel inner panels.
CB40E - 3 outer panels and 2 inner panels.

Turn off unit and allow to cool to room temperature. Remove the safety
glass and firebox glass — see manual for instructions

3. Install outer safety glass.

4. Reverse steps to remove panels.

Panel Clips

Location of

Regency Logo

CITY SERIES

Inner Panels

Outer Panels

Painted Panel Installation

The ACB40E can be equipped with optional steel inner panels— 3 outer
panels and 2 inner panels.

Summary of Contents for City ACB40ELP
























































































Search results

Summary of Contents for City ACB40ELP

Reviews:

Related manuals for City ACB40ELP

Brands by name

Popular brands

Regency Fireplace Products City ACB40ELP, Owners & Installation Manual

Search results

Summary of Contents for City ACB40ELP

Reviews:

Related manuals for City ACB40ELP

Brands by name

Popular brands