Regency Fireplace Products City ACB40ELP Owners & Installation Manual Download Page 28

Page: 28 / 87

City Series ACB40E

installation

919-669c

01.19.17

CITY SERIES

15. Attach Part L to the front of the LEFT and RIGHT sides with 2 screws

on each side.

16. Position Part I (x2) to fi t in the indent in Part S and Part H, secure

each Part I with 8 screws each - 4 top/4 bottom.

17. Position Part M (x2) to nest in behind Part I (x2) and secure to Part

I with 3 screws each and Part L with 4 screws each.

See 2 drawings shown below noting orientation of Part M.

Attach Part I (x2) to Part S & H

Attach Part M (x2) to Part L

Part I screw holes located on the side

Attach Part L (x2) to LEFT and RIGHT sides

14. Secure Part Q to top Part S with 1 screw each.

Part L

Part M

Part H

Part Q

Part S

Part I

Screw holes in Part I

located on the side

Part M

Summary of Contents for City ACB40ELP
























































































Search results

Summary of Contents for City ACB40ELP

Reviews:

Related manuals for City ACB40ELP

Brands by name

Popular brands

Regency Fireplace Products City ACB40ELP, Owners & Installation Manual

Search results

Summary of Contents for City ACB40ELP

Reviews:

Related manuals for City ACB40ELP

Brands by name

Popular brands