Regency Fireplace Products City ACB40ELP Owners & Installation Manual Download Page 60

Page: 60 / 87

City Series ACB40E

installation

City Series 40 ACB40E

920-206

12.18.19

OPTIONAL FAN KIT INSTALLATION

NOTE: Installation of Fan Kit should be done prior
to installation of the wall.

Mount and secure the fan housing assembly to

framing members, the front of the fan housing will

protrude 12.7mm out of the wall so it may be finished

with

plasterboard

, etc. See diagram 2

3. Install the air duct run. Secure the duct to the duct
collar on the unit and the fan housing with 3 screws
per end and aluminum duct tape.

Diagram 2: Side View - Secure fan housing

to minimum 45mm framing.

Diagram 1:

Front View

Round Air Duct: Attach the 152.4mm round air duct

(supplied) to the fireplace collar and run the duct to

the fan housing. Attach the round-to-oval adapter
to the fan housing and the air duct to the adapter

45mm

Round to Oval

Adapter

Fan Housing

Secure with 3 Screws and

Aluminum Duct Tape at Unit

Air Duct

7. Screw the Register Adapter Frame and the
Air Register to the Fan Housing See diagram 4.

Diagram 4

4. Install the On/Off switch in a convenient location.

This switch controls the fan operation.

NOTE: Variable speed or Rotary 3 speed switch

can be fitted.

5. Wire up the the fan, wall switch and power supply
per local codes. See wiring diagram as reference.
*Electrician to supply wiring.

6. Screw fan junction box to the fan housing.

45mm

Finished

Surface

(12mm)

Front

of Fan

Housing

Adjustable

Brackets for

different

wall/floor

thickness.

(12mm)

8. Attach collar to base of adaptor with 4 screws

as shown below.

9. Attach assembly to unit in location shown below

with 4 screws.

NOTE: Heatwave adaptor may be installed on

either left of right side.

Summary of Contents for City ACB40ELP
























































































Search results

Summary of Contents for City ACB40ELP

Reviews:

Related manuals for City ACB40ELP

Brands by name

Popular brands

Regency Fireplace Products City ACB40ELP, Owners & Installation Manual

Search results

Summary of Contents for City ACB40ELP

Reviews:

Related manuals for City ACB40ELP

Brands by name

Popular brands