Reeves G2 series Operation Manual Download Page 37 | Manualshive

Page: 37 / 183

background image

Operation & Maintenance w/IPB

G2 Series Decontamination Water Heater

0007

Part Number 1006375

0007-1

DHS SYSTEMS, LLC

This document contains information proprietary to DHS Systems LLC and is intended solely for use by its customers. No portion of this document may be reproduced
for release to a third party without written consent of DHS Systems LLC.

OPERATOR INSTRUCTIONS

G2 SERIES DECONTAMINATION WATER HEATER

G2 SERIES START-UP PROCEDURES

GENERAL

The following WP details the start-up, hot water operation and solution injector operation (G2-I and G2S-I Water
Heater Only) procedures of the G2 Series Decontamination Water Heater.

WARNING

INCORRECT OPERATION OF THIS WATER HEATER COULD RESULT IN
SERIOUS INJURY AND ORDAMAGETO THE EQUIPMENT. DO NOT
ALTER OR MODIFY THIS EQUIPMENT IN ANY MANNER.

START-UP PROCEDURES

NOTE

Ensure the injector bypass lever (G2-I and G2S-I Water Heater Only) is in the
OFF position.

1. Locate safety decals on the water heater and heed their warnings.

2. Fill the burner fuel tank with #1 or #2 fuel oil, diesel or kerosene.

3. Connect the power supply GFCI power cord into an 110V power supply, ensuring the outlet matches the plug on
the power cord.

NOTE

Prior to connecting the water supply source hose, ensure hose has been
flushed in accordance with WP 0006.

4. Connect the water supply hose to water source inlet of the water heater.

NOTE

Flush coil prior to connecting discharge hoses

5. Connect fresh water discharge hose (Black) and Decon solution discharge hose (Red) (G2-I and G2S-I Water
Heater Only) or another black hose(s) to the corresponding water discharges on the unit.

6. Connect the “male” end of the hose to the shower system (G2-I or G2S-I water Heater).

7. Turn the temperature control valve knob clockwise (CW), to the OFF position.

8. Open the water supply completely to charge the water heater.

9. Open the temperature control valve knob, counter-clockwise (CCW), until water begins to flow from the shower
heads (G2-I or G2S-I water Heater).

10. Allow the water to flow until all air is released from the system.

11. Once the system is in full flow, turn the power ON/OFF switch to the ON position.

END OF TASK

«
...
35
36
37
38
39
...
»

Summary of Contents for G2 series
























































































































































































Reviews:

No comments

Related manuals for G2 series

Brand: Eagle Pages: 16

Brand: Ultimate Products Pages: 58

Brand: Saci Pages: 24

Brand: PAC Pages: 30

Brand: Calpeda Pages: 4

the Vac Q SBL002

Brand: Sage Pages: 80

Brand: PAPILLON Pages: 22

Brand: Wayne Pages: 8

Brand: Wayne Pages: 20

Brand: Wayne Pages: 8

Brand: Wayne Pages: 12

Brand: Dancover Pages: 7

Brand: AMICUS Pages: 12

Brand: Napoleon Pages: 32

Brand: Sicce Pages: 24

Brand: HearthRite Pages: 24

Brand: Sure Flame Pages: 32

Brand: Kamoer Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands