Reeves G2 series Operation Manual Download Page 109

Page: 109 / 183

Operation & Maintenance w/IPB

G2 Series Decontamination Water Heater

0015

Part Number: 1006375

0015-21

DHS Systems LLC

This document contains information proprietary to DHS Systems LLC and is intended solely for use by its customers. No portion of this document may be reproduced
for release to a third party without written consent of DHS Systems LLC.

INSTALLATION OF POWER SWITCH (CONT):

c. Raise control panel and keep pressure against the panel while installing the mount bolts.

d. Using a 7/16” open end wrench, install and tighten (4) bolts, (4) lock washers and (4) flat washers.

e. Reinstall water supply connector protective cover, hand tight.

Reinstall (4) cam covers on the fresh water and Decon solution outlets.

g. Reconnect power cord to power supply outlet.

h. Perform operation check on the power switch.

END OF TASK

Summary of Contents for G2 series
























































































































































































Search results

Summary of Contents for G2 series

Reviews:

Related manuals for G2 series

Brands by name

Popular brands

Reeves G2 series, Operation Manual

Search results

Summary of Contents for G2 series

Reviews:

Related manuals for G2 series

Brands by name

Popular brands