manualshive.com logo in svg

Red Seal Measurement Datamate 2200, Operating & Maintenance Manual

Share
Download
Red Seal Measurement Datamate 2200 Operating & Maintenance Manual Download Page 94

Datamate 2200 O&M

Page 88

 

9.7.4  Display Setup Configuration 

 

 

Within this menu the display can be set up to display three variables at one time 

on the LCD display. 

 

 

Using the CONFIGURATION MENU TREE enter the Display Setup Configuration. 

 

 

The following chart highlights the Display Setup Configuration.

 

Menu or Display  Description

 

Configuration 

The Datamate 2200 will allow the user to program three variables as a default on 

 

4. Display  

the optional LCD display. If you wish to configure the display, press ENTER. 

Use the up arrow key to select the default variable for Line 1. 

 

 

Line 1

 

 

[XXXXXXXXXXX] 

 

 

If you wish to configure the display for Line 2 press ENTER

 

 

Line 2

 

 

[XXXXXXXXXXX] 

 

 

 

If you wish to configure the display for Line 3, press ENTER

 

 

Line 3

 

 

[XXXXXXXXXXX] 

Summary of Contents for Datamate 2200

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands