Red Seal Measurement Datamate 2200 Operating & Maintenance Manual Download Page 63

Page: 63 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Calibration

Diagnostic

Datamate 2200 O&M

Page 57

9.4 Program Mode

The program mode for the Datamate 2200 transmitter provides access to the user based

on the password level. A clear explanation of access to the program mode and the

password levels is listed below.

Menu or Display

Description

Main Menu

This menu gives the user the ability to view and program the Datamate

4. Program

2200 based on his/her password ‘level.’ When ENTER is pressed ‘ENTER

PASSWORD’ is displayed. The password is then entered using the keypad.

Entering the proper ‘level’ password allows access to configuration and

programming features.

The default passwords are:

11 for levels 0 and 1, and

22 for level 2.

Level 0 and 1 passwords (11) only allow reviewing the configuration and

programming data.

Level 2 passwords (22) allow changing the user/application configuration

and programming

Summary of Contents for Datamate 2200

































































































































Search results

Summary of Contents for Datamate 2200

Reviews:

Related manuals for Datamate 2200

Brands by name

Popular brands

Red Seal Measurement Datamate 2200, Operating & Maintenance Manual

Search results

Summary of Contents for Datamate 2200

Reviews:

Related manuals for Datamate 2200

Brands by name

Popular brands