Red Seal Measurement Datamate 2200 Operating & Maintenance Manual Download Page 93

Page: 93 / 128

Intro

Read This

First

Transmitter

Installation

Power Supply

Wiring

I/O

Wiring

Batch

Wiring

Startup

Trouble-

shooting

Program-

ming

Main

Config

System

Model

Numbers

Xmitter

Specs

Return

of Goods

Calibration

Diagnostic

Datamate 2200 O&M

Page 87

9.7.3 Alarm Setup Configuration

The Datamate 2200 transmitter has two high and low external alarms. These

alarms can be programmed to represent any variable and system alarm.

Using the CONFIGURATION MENU TREE enter the Alarm setup configuration.

The following chart highlights the Alarm Setup Configuration.

Menu or Display Description

Configure Alarms If you wish to configure Alarm 1, press ENTER. Press the up arrow key to

1. Alarm 1

select the alarm function. High and low setpoints can be configured.

Alarm

[Select Alarm Output]

2. Alarm 2

If you wish to configure Alarm 2, press ENTER. Press the up arrow key to

select the alarm function.

Alarm

[Select Alarm Output]

3. Startup Delay

If a delay is required for the startup of the alarm, press ENTER.

Press the up and across keys to set the delay.

Startup Delay

[XXXXXXXXXX]

4. Exit

To exit Configuration Alarm menu press ENTER

Summary of Contents for Datamate 2200

































































































































Search results

Summary of Contents for Datamate 2200

Reviews:

Brands by name

Popular brands

Red Seal Measurement Datamate 2200, Operating & Maintenance Manual

Search results

Summary of Contents for Datamate 2200

Reviews:

Brands by name

Popular brands