manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 6 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 6

Changing Hard Drive Configuration ..................... 29

 

Modifying Partitions ............................................. 30

 

Another Look at the MicroDrive Installer.............. 30

 

New Hard Disk Setup ........................................... 31

 

Installing the GS/OS Driver .................................. 32

 

Using Two Hard Disk Drives................................. 33

 

Setting the Hard Drives' Jumpers .......................... 33

 

In a One-Drive Configuration..................................... 33

 

In a Two-Drive Configuration .................................... 33

 

Booting from a Different Volume .......................... 34

 

AE Vulcan Upgrade ................................................... 35

 

Hard Disk Back Up ............................................... 35

 

Setting Up the Hard Drive .................................... 35

 

Error Messages at Boot Time ................................ 36

 

Drive 1 Error ............................................................... 36

 

Missing configuration data ......................................... 36

 

Error reading boot sector ........................................... 36

 

Volume not formatted ................................................. 37

 

Unable to load ProDOS .............................................. 37

 

Problematic Hard Disk Drives .................................... 38

 

WD Caviar Series .................................................. 38

 

HD Installation ............................................................ 39

 

IDE Interface Overview .............................................. 41

 

Introduction ......................................................... 41

 

The IDE Interface ................................................. 41

 

IDE Origins .......................................................... 42

 

The Evolution of IDE (ATA): ...................................... 43

 

Compact Flash Overview .......................................... 44

 

What is a CF Storage Card? ................................... 44

 

CF Card Internal Diagram .......................................... 44

 

MicroDrive Turbo Revision History ............................. 45

 

First DMA IDE Controller...................................... 45

 

Card Revisions ............................................................ 45

 

Online Review ............................................................. 45

 

 

 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments