manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 23 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 23

 

MicroDrive Turbo 

16 

ReActiveMicro 

 

 

Raw Disk Copier 

You can use a utility to Back-up the whole CF Card using a program called HDD Raw 
Copy, download link: 

HDD Raw Copy Tool

 

CiderPress

 however has the advantage of being able to open and utilize the backup 

Images it creates. So in the future you could copy files from the Images or access 
data if needed. You would not need to fully restore the Image as with other backup 
programs. 

Some Emulators can also access and use the Image files too. Raw Disk Copiers like 
HDD Raw Copy can however be useful if you would like to quickly duplicate a CF 
Card as it will copy the Partition information unlike 

CiderPress

.  So you do not need 

to run the 

MicroDrive Turbo

 Setup Utility before restoring the HDD Raw Copy Image. 

This could be a useful backup method should the Setup Utility backup disk you 
made see

 Backing Up - Setup Utility

 above ever becomes damaged, lost, or 

unusable. 

 

 

 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments