manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 45 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 45

 

MicroDrive Turbo 

38 

ReActiveMicro 

 

 

Problematic Hard Disk Drives 

 

CP30204: Universal translation mode does not work correctly, replaced by CP30254. 
CP30104, 105 Mbytes Version: Universal translation mode does not work correctly. 
The 120Mbyte version of this drive (CP30104) works fine. 

 

Model: ST1144A: Unable to read or write 256 sectors at a time, this is required for the 

MicroDrive Turbo 

Card. 

 

It is recommended that you use only WD drives manufactured in 1994 or later. 

WD Caviar Series 

If you want to use a WD Caviar Series Hard Disk Drives with the 

MicroDrive Turbo

 

Card, you will have problems with the original 

MicroDrive Turbo

 software (this is the 

firmware marked Apple II

GS

 Rev. 1.2x and its GS/OS driver v2.xx). 

The WD Digital Hard Drives cannot be handled on the Apple II

GS

 like other IDE 

drives, they require special handling due to some very special properties of these 
drives. 

To use a WD Caviar Hard Drive, you need to re-burn your existing firmware EPROM 
on the 

MicroDrive Turbo

 Card. The image of the firmware v1.5x for the EPROM is 

included in this folder. If you cannot do it yourself, ask a friend or somebody at your 
local computer group whether he can erase and burn a 27C512 EPROM for you. 
Otherwise, send a request to us for getting a new EPROM. 

You must also use the special GS/OS driver (file name is 

MicroDrive.v1.5

) provided in 

this folder. 

If you try to use a different driver, nothing serious will happen, however, you won't 
get the benefits (i.e. speed) from the driver's functions because it will refuse to work 
with this version of the firmware. 

 

 

 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments