manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 27 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 27

 

MicroDrive Turbo 

20 

ReActiveMicro 

 

 

Self-Powered IDE to CF Adapters 

The 

MicroDrive Turbo

 comes with a self-powered IDE to CF Adapter with a pre-setup 

CF Card. Self-powered refers to the IDE to CF Adapter which uses power supplied on 
Pin 20 of the IDE connector and does not require an external power source. This 
means the Apple II Computer can supply power to the CF Card and no other power 
source is needed. 

Boards sold from 2006 to Mid-2008 will have +5v connected to Pin 20 of the IDE 
Connector in the form of a small jumper wire on the rear of the board. Later boards 
have a small trace added to the face, left side of the board. 

Over the years some users insisted on trying to install the CF Adapter backwards 
which would cause a short and burn the added trace from the board. So all boards 
from late 2017 and on have a fuse added to the small trace for added protection. 

The photo below on the right with the fuse displays what the added trace looks like 
and its location. 

IDE Pin 20 Power Mods 

 

Pre-2008 MicroDrive Turbo 

 

Flywire Power Mod and 

Self Powered CF Adapter. 

 

2018 MicroDrive Turbo 

F1 Fuse and 

Self Powered CF Adapter. 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments