ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 10

Page: 10 / 55

MicroDrive Turbo

ReActiveMicro

ProDOS 8 and 16

The

MicroDrive Turbo

is ProDOS compatible. It's recognized as a

Standard Mass

Storage Device

just like any Hard Disk Drive on your Apple II. Large Volume DOS

3.3 support is provided through the use of a program called

DOS.MASTER

(preloaded on CF Card).

Boot Options

By default, Volume 1 is set to boot. However, when setting up a New CF Card the
user sets which Volume they desire to boot. Or on an existing CF Card the Setup
utility can modify the default boot Volume. The

MicroDrive Turbo

also offers a

temporary option to boot to ANY volume.

When powering on the Apple II the user will press and hold the



key. This will

pause the

MicroDrive Turbo's

splash screen.

The user then presses the corresponding Volume's number key, and the

MicroDrive

Turbo

will boot to that Volume.

Apple II

and Apple IIe Enhanced Operation

The

MicroDrive Turbo

comes standard with the Apple II

Firmware. You can

however order one with Apple IIe Firmware, or buy an upgrade ROM to convert a
II

MicroDrive Turbo

for use in an Apple IIe Enhanced.

Summary of Contents for MicroDrive Turbo
























































Search results

Summary of Contents for MicroDrive Turbo

Reviews:

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 10 / 55

Search results

Summary of Contents for MicroDrive Turbo

Reviews: