manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 7 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 7

 

 

A Word About This Manual 

Congratulations on your purchase of the 

MicroDrive Turbo

 from 

ReActiveMicro.com 

This manual is designed to assist you in every phase of integrating the 

MicroDrive 

Turbo

 Expansion Card into your Apple® II

GS

™ and Apple® IIe™ Enhanced Personal 

Computer. 

The manual covers everything from the hardware installation, software configuration, 
and much more. The hardware is the most sensitive part; an improperly-performed 
hardware installation could damage the 

MicroDrive Turbo

 and the Apple Computer. 

The 

MicroDrive Turbo

 is an Apple II Expansion Card that gives the Apple II

GS

 and 

the Apple IIe Enhanced Personal Computer a complete Solid State Storage Solution. 

Everything is included to get you up and running right out of the box. 

There are two categories of Apple II owners: those who have installed peripheral 
cards into their computers, and those who haven't.  

Those of you who have ventured under the hood of their computer probably need 
little explanation of the process. You will see that the 

MicroDrive Turbo’s

 installation 

is not much more difficult than any other card in your system. 

Those of you who have never explored the insides of your computer the installation 
is not difficult if you follow the detailed steps in the Installation section. 
Nevertheless, you may decide that this process is not for you; in this case, arrange for 
a qualified computer technician to install the 

MicroDrive Turbo

 Expansion Card for 

you.  

No matter what your level of experience, do not attempt to install 

MicroDrive Turbo 

until you have read the manual and understand all of the steps completely. 

Static Precaution 

Avoid any and all electrostatic discharges to the 

MicroDrive Turbo

 Expansion Board. 

Like all electronics devices, a static discharge can destroy or shorten the life span of 
the delicate components on the Expansion Card. 

This risk is highest in areas where there is carpet, and especially during dry weather. 

You can momentarily discharge any buildup by coming into contact with a grounded 
piece of metal, the most convenient method is touching the metal case of the Apple 
II’s internal power supply, the computer must be plugged in for this procedure to 
work, the power cable has the grounded connection. 

 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments