manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 44 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 44

 

MicroDrive Turbo 

37 

ReActiveMicro 

 

 

Volume not formatted 

This error message is related to the volume you want to boot from. 

The 

MicroDrive Turbo

 Card could load a configuration, but it could not find anything 

that looks like a PRODOS boot sector. This sector is usually present after a volume 
has been high-level formatted by a system utility like the Finder etc. 

Unable to load ProDOS 

This message appears if the ProDOS boot routine (located on the boot sector of any 
PRODOS volume and loaded into the computer's memory at boot time) has found 
one of the following errors: 

a)

 

The boot routine cannot find a directory structure on the boot volume 
(directory may be damaged) 

b)

 

The boot routine cannot find a file with the name PRODOS in the root 
directory of the current boot volume. The file PRODOS usually is the 
PRODOS 8 operating system or the file that launches GS/OS 

c)

 

While loading PRODOS, a read error occurs because of a bad sector 
belonging to the file PRODOS. 

 
 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments