manualshive.com logo in svg

ReActiveMicro MicroDrive Turbo, Owner'S Manual, Page: 51 / 55

Share
Download
ReActiveMicro MicroDrive Turbo Owner'S Manual Download Page 51

 

MicroDrive Turbo 

44 

ReActiveMicro 

 

 

Compact Flash Overview 

What is a CF Storage Card? 

The CompactFlash Storage Card contains a single chip controller and flash memory 
module(s) in a matchbook-sized package with a 50-pin connector consisting of two 
rows of 25 female contacts each on 50 ml (1.27 mm) centers. 

The controller interfaces with a host system allowing data to be written to and read 
from the flash memory module(s). 

The CompactFlash Storage Cards on-card intelligent controller manages interface 
protocols, data storage and retrieval as well as Error Correcting Code (ECC), defect 
handling and diagnostics, power management and clock control. Once the 
CompactFlash Storage Card has been configured by the 

MicroDrive Turbo

, it appears 

as a standard ATA (IDE) disk drive. 

CF Card Internal Diagram 

 

For more information on this type of storage device: 

compactflash.org 

 

MicroDrive Turbo 
Apple II Expansion 

 

 

 

 

  

 

Controller 

 

 

 

  

 

Flash 

Module(s) 

 

 

 

  

 

CompactFlash Storage Card 

Summary of Contents for MicroDrive Turbo
























































Reviews:

No comments