background image

Cyclone RazorOptimal User Manual

 

5 | 

P a g e

 

Technical Services, Inc. 

8.  Maintain and clean machine at recommend intervals. Intervals may need to be adjusted due to 

work load or material type to keep machine in top condition. Follow instructions for lubrication, 
setup, and changing accessories 
 

9.  Disconnect machine from power source before, changing accessories, or any servicing activity. 

 

10.  Avoid accidental starting. Make sure switch is in the off position before connecting to power. 

 

11.  Remove any tools or loose objects from work surface of machine. Make sure any tools used for 

adjustment  or  maintenance  are  removed  from  machine  before  machine  is  restarted.  Make  a 
habit of scanning for tools and scraps every time the machine is started. 
 

12.  Keep  work  area  clean.  Cluttered  work  areas  and  workbenches  increase  the  likelihood  of  an 

accident. 
 

13.  Do not use in dangerous environments. Do not use machine in damp or wet locations, or expose 

them to rain. Keep work area well illuminated. 
 

14.  Keep children away. All visitors should be kept at a safe distance from work area. 

 

15.  Make workshop childproof, with padlocks, master switches, or by removing starter keys. 

 

16.  Do not force the machine. It will function better and safer at its designed rate. 

 

17.  Use the right tools. Do not force the machine or attachments to do a job for which they were not 

designed. Contact the manufacturer or distributor if there is any question about the machine’s 
suitability for a particular job. 
 

18.  Use  only  recommended  accessories.  Consult  the  operation  manual  for  recommended 

accessories. 
 

19.  Wear proper apparel. Avoid loose clothing, gloves, neckties, rings bracelets, or  jewelry  which 

could be tangled in moving parts. Keep long hair contained to prevent entanglement. Non-slip 
footwear is recommended. 
 

20.  Always wear safety glasses. 

 

21.  Secure the work piece. 

 

22.  Keep proper footing and balance at all times. 

 

23.  Do not use machine while under the influence of drugs, alcohol, or any medication. 

 

24.  Always  wear  a  face  mask  or  dust  mask  if  operation  creates  excessive  dust  or  chips.  Always 

operate machine in a well-ventilated area and provide proper dust removal. 
 

25.  Never leave machine running unattended. Turn power off. Do not leave machine until it comes 

to a complete stop.  

 

 

 

 

Summary of Contents for Cyclone RazorOptimal
























































Reviews: