Raytech WR14 Instruction Manual Download Page 23 | Manualshive

Page: 23 / 119

background image

Version 3.03

WR14 / WR50-12/13 Winding Resistance Meter Instruction Manual

22

GROUND TERMINAL

Use this terminal to connect an additional ground line even if your mains Power cable (Mains) provides
an Earth ground line. Also, use it even if you are not sure that the local installation Earth ground is a low
resistive ground.

EXTERNAL

This port is used for an external warning device. See the chapter on interfaces for more details.

TEMPERATURE RECEPTACLE

These two (2) receptacles are for the external temperature probes (Optional accessory part number:
2021N-26001).

POTENTIAL RECEPTACLE

Connect positive (+) and negative (-) potential cables for each channel to the test object.

CURRENT RECEPTACLE

Connect positive (+) and negative (-) current cables for each channel to the test object.

SAFETY INDICATOR

Green Light

on:

System is in safe standby mode. Ready for handling test leads and connections.

Red Light

on:

Unsafe mode! Do NOT remove any cables. There is current flowing and voltage on

the test leads. System is testing.

WARNING!

The transformer is not discharged!

EMERGENCY STOP

Press to Stop. The measurement will stop and immediately begin to discharge the transformer. Turn
clockwise to release. The device will remain in a safe mode state.

MAINS INPUT

Connect a power cord to the Mains Input (88 to 264 V / 47 to 63 Hz).

«
...
21
22
23
24
25
...
»

Summary of Contents for WR14
























































































































Reviews:

No comments

Related manuals for WR14

Brand: Keithley Pages: 49

NUFLO Scanner 2000 microEFM

Brand: Cameron Pages: 8

Brand: E+E Elektronik Pages: 32

DT4120 PS Series

Brand: Datcon Pages: 92

miniSERIES Series

Brand: Valeport Pages: 25

Seeker 400 Series

Brand: General Pages: 24

Brand: shelyak Pages: 45

Brand: Heyuan Intelligence Pages: 14

Brand: DAKOTA ULTRASONICS Pages: 51

SensoDirect Con200

Brand: Lovibond Pages: 24

EnviroMentor Field Finder

Brand: Radians Innova Pages: 12

Brand: Parkside Pages: 165

Brand: Aventics Pages: 23

Brand: PCE Instruments Pages: 25

Brand: JGR Pages: 54

Brand: Teledyne Lecroy Pages: 8

Brand: Bushnell Pages: 76

Brand: Anritsu Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands