Raytech WR14 Instruction Manual Download Page 98

Page: 98 / 119

WR14 / WR50-12/13 Winding Resistance Meter Instruction Manual

Version 3.03

SERVICE MODE

The Service Mode has limited access. There are several codes accessible for setting parameters.

From the main screen press 'Setup'. Then in the
General screen press 'Service Mode'. Enter the
corresponding code or Exit by pressing '#'.

CALIBRATE TOUCHSCREEN

The touch screen parameters can be calibrated by the end user. Enter code

0000#

and follow the on

screen instructions as depicted below.

You will see the following screen:

Press and hold the stylus on the center of the target
until the cross moves.

Repeat as the target moves around the screen.

If a keyboard is connected, press Enter to accept
the new parameters or Esc to escape.

If a keyboard is not connected, press anywhere on
the screen to accept the new parameters.

Summary of Contents for WR14
























































































































Search results

Summary of Contents for WR14

Reviews:

Related manuals for WR14

Brands by name

Popular brands

Raytech WR14, Instruction Manual

Search results

Summary of Contents for WR14

Reviews:

Related manuals for WR14

Brands by name

Popular brands