Raven Sidekick Pro ISO Installation & Operation Manual Download Page 52

Page: 52 / 82

HAPTER

Sidekick Pro™ ISO Installation & Operation Manual

b. Toggle the selected injection pump master switch to off.

SIDEKICK PRO™ ISO OPERATION

Each Sidekick Pro ISO injection pump may be monitored during field operations via the UT display using the

respective Product Control Home screen.
1. Select the UT display menu.

2. Locate the ISO injection pump icon in the UT menu similar to the following.

NOTE:

The UT menu will display a pump icon for each pump detected on the ISOBUS system.

3. The Product Control Home screen will be displayed.

Soft Keys

Master

Switch

Rate Increase

Rate Decrease

Tools

Product Totals

Rates Area

Speed Display

Carrier and

Injection Pressure

Display

Chemical

Injection Tank

Volume

Section

Status

Display

Flow

Rate

Active

Agitation

Summary of Contents for Sidekick Pro ISO


















































































Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands

Raven Sidekick Pro ISO, Installation & Operation Manual

Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands