Raven Sidekick Pro ISO Installation & Operation Manual Download Page 42

Page: 42 / 82

HAPTER

Sidekick Pro™ ISO Installation & Operation Manual

FIGURE 2. Boom Pressure Transducer Location

NOTE:

Sidekick Pro ISO uses these pressure transducers to verify injection status and for error detection.

To calibrate the pump transducer:

NOTE:

The following process offers a general overview of calibrating or resetting the Sidekick Pro ISO pump

pressure transducer. Refer to the operation manual for the specific control console for detailed

navigation and calibration of the pressure transducer or pressure display.

1. Turn off the injection pump and product control system and ensure there is no pressure at the pump outlet

port.

2. Select or display the set up screens for the correct product.
3. Verify no product pressure is in the injection lines.
4. Enter a value of zero for the pressure calibration value.

RATE BUMP (±)

Enter the desired rate change when using the rate increase (+) or decrease (-) soft keys on the product control

home screen.

NOTE:

The rate increase and decrease feature is only functional when the injection product is set to either

automatic or Rx mode.

Optional Boom Pressure

Transducer

Summary of Contents for Sidekick Pro ISO


















































































Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands

Raven Sidekick Pro ISO, Installation & Operation Manual

Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands