Raven Sidekick Pro ISO Installation & Operation Manual Download Page 35

Page: 35 / 82

CHAPTER

P/N 016-0171-509 Rev. E

CHAPTER 4

CALIBRATION

DETECTING AND ADDRESSING THE MOTOR CONTROL NODE

When the system is first powered on after installing a Sidekick Pro™ ISO injection pump, the pump control node

will initially be assigned an address of “0” on the ISOBUS. To readdress the Sidekick Pro ISO control node:

NOTE:

If the node is not detected on the ISOBUS, see Chapter 6, Injection Diagnostics and Troubleshooting,

to troubleshoot the control node and ISOBUS system.

1. Select the UT display menu.

2. Locate the ISO injection pump icon in the UT menu similar to the following.

The UT menu will display a pump icon for each pump detected on the ISOBUS system.

3. Select the injection pump icon to display the main product control screen for the selected injection pump.

NOTE:

If more than one injection pump is detected on the ISOBUS system, each pump will have a separate

product control screen for calibrating or operating each pump. Be sure to access each control screen

to calibrate or operate the appropriate pump(s).

Summary of Contents for Sidekick Pro ISO


















































































Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands

Raven Sidekick Pro ISO, Installation & Operation Manual

Search results

Summary of Contents for Sidekick Pro ISO

Reviews:

Brands by name

Popular brands