manualshive.com logo in svg

Raven AutoBoom XRT, Calibration & Operation Manual

Share
Download
Raven AutoBoom XRT Calibration & Operation Manual Download Page 9

CHAPTER

2

P/N 016-0235-001 Rev. B

5

CHAPTER 2

INTRODUCTION

Raven’s latest advancement in boom controls in AutoBoom® XRT. Industry-leading radar sensor technology uses 

simultaneous ground and canopy detection to maintain optimal spray height for maximum product efficacy. 

Pressure-based control allow for smooth movement and quicker reaction time while center rack stability 

technology with optional dampers gives the operator complete control, maximizing boom life.

INSTALLATION

RECOMMENDATIONS

Before installing the AutoBoom XRT system, park the machine where the ground is level, clean, and dry. Bleed 

pressure from the hydraulic system and leave the machine turned off for the duration of the installation process.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this 

manual as you complete the installation process.

Raven Industries recommends the following best practices when installing or operating the XRT system for the first 

time, at the start of the season, or when moving the AutoBoom XRT system to another machine:
• Verify that the machine’s hydraulic system is using fresh oil and that the filters have been recently changed
• Ensure there are no issues with the machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine 

metal deposits in the hydraulic hoses, etc.).

POINT OF REFERENCE

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

 

WARNING

Carefully read and follow all safety requirements 

and precautions contained in this manual and the 

machine-specific Installation Manual. Failure to 

follow safety instructions may lead to equipment 

damage, personal injury, or death.

Summary of Contents for AutoBoom XRT









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands