Raven AutoBoom XRT Calibration & Operation Manual Download

Page: 14 / 72

HAPTER

AutoBoom XRT Calibration & Operation Manual

TABLE 1. Sensor Reading States

AUTOBOOM XRT OPERATION

RUN SCREEN OPERATION

FIGURE 4. Run Screen

1. Press the desired boom or the XRT widget to enable or disable AutoBoom XRT.
2. Press and hold the desired boom to open additional boom information. Pressing and holding also allows the

user to turn off the master switch.

Image

Status

Description

Sensor Working/Reading

Indicates the sensor is functioning properly and reading

the desired target.

Sensor Not Reading/

Malfunctioning

If there is an X through the sensor, the sensor is not

reading a target or is malfunctioning.

Sensor Offline/Disabled

If there isn’t a number below the sensor location, the

sensor may be offline or was disabled by the user.

XRT

Operation

Summary of Contents for AutoBoom XRT








































































Search results

Summary of Contents for AutoBoom XRT

Reviews:

Related manuals for AutoBoom XRT

Brands by name

Popular brands

Raven AutoBoom XRT, Calibration & Operation Manual

Search results

Summary of Contents for AutoBoom XRT

Reviews:

Related manuals for AutoBoom XRT

Brands by name

Popular brands