manualshive.com logo in svg

Raven AutoBoom XRT, Calibration & Operation Manual

Share
Download
Raven AutoBoom XRT Calibration & Operation Manual Download Page 64

C

HAPTER

 7

60

AutoBoom XRT Calibration & Operation Manual

TARGET HEIGHT TEST

This test is similar to the Target Position Test but incorporates all of the sensors on the machine to control the 

ground height.

FIGURE 15.  Target Height Test

TERRAIN COMPENSATION TEST

The Terrain Compensation Test analyzes data from the inertial sensors in the XRT ABM ECU.

At the start of the test, the user is asked to have the engine idling at low speed. Next the user is asked to run the 

engine at typical operating RPM. The test reports a pass or fail for each engine speed. If the test fails, engine 

vibrations may be having a negative impact on system performance.

NOTE:

If the test fails, check the node installation. Verify the node is mounted securely and has not come 

lose during operation. Also confirm that the node is mounted as instructed in the AutoBoom XRT 

machine specific installation manual.

The AutoBoom XRT system will still operate if the test fails, however, terrain compensation features 

may not offer optimal boom height adjustments for all terrain features.

Summary of Contents for AutoBoom XRT









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands