RAM Ram 2012 Page 86 Owner'S Manual Download | Manualshive

Page: 86 / 173

background image

WARNING!

A fire may result if fuel is pumped into a portable
container that is on a truck bed. You could be burned.
Always place fuel containers on the ground while
filling.

Fuel Filler Cap

If the fuel filler cap is lost or damaged, be sure the
replacement cap is for use with this vehicle.

CAUTION!

Damage to the fuel system or emission control sys-
tem could result from using an improper fuel tank
filler tube cap. A poorly fitting cap could let impuri-
ties into the fuel system.

WARNING!

•

Never have any smoking materials lit in or near
the vehicle when the fuel filler cap is removed or
the tank filled.

•

Never add fuel to the vehicle when the engine is
running.

Avoid Using Contaminated Fuel

Fuel that is contaminated by water or dirt can cause
severe damage to the engine fuel system. Proper main-
tenance of the engine fuel filter and fuel tank is essential.
Refer to “Maintenance Procedures” in “Maintaining Your
Vehicle” for further information.

Bulk Fuel Storage – Diesel Fuel

If you store quantities of fuel, good maintenance of the
stored fuel is also essential. Fuel contaminated with
water will promote the growth of “microbes.” These

84

STARTING AND OPERATING

«
...
84
85
86
87
88
...
»

Summary of Contents for Ram 2012














































































































































































Reviews:

No comments

Related manuals for Ram 2012

Brand: AA Products Pages: 6

Brand: Camcar Pages: 6

Brand: Ford Pages: 52

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

Brand: Pacbrake Pages: 14

PERFECTVIEW CAM80AHD

Brand: Dometic Pages: 196

Brand: Ford Pages: 2

Autostacker PL-6SR

Brand: BendPak Pages: 104

Brand: Whipple Pages: 3

Brand: walser Pages: 24

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: METRON Pages: 4

Brand: Hyundai Pages: 19

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: Cadillac Pages: 402

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands